CSCS Supervisor Mock Test

0 votes, 0 avg

Specialists Test

Supervisory

1 / 72

What is the maximum vertical height that a fixed ladder can be climbed, before an intermediate landing place is required?

9 m

7.5 m

8.5 m

8 m

2 / 72

Under the Construction (Design and Management) Regulations 2015, which two of the following must you ensure workers have received before they start working on site?

A suitable site induction, specific to the work

Confirmation of their working hours and rest break

Details of the client's brief and project expectations

Information on relevant hazards and control measures

Details of the designer's plan of work

3 / 72

What does a COSHH assessment tell you?

How to use a substance safely in the environment in which it is to be used

How to assess noise levels to protect your hearing

How to work safely in confined spaces

How to lift heavy loads and how to protect yourself

4 / 72

Under the Construction (Design and Management) Regulations 2015, which of the following must be in place before demolition work can start?

A demolition risk assessment

A health and safety file

The arrangements for demolition recorded in writing

The pre-tender demolition health and safety plan

5 / 72

What is the best way for a supervisor or manager to make sure that the operatives doing a job have fully understood a method statement?

Put the method statement in a labelled ring-binder in the office

Explain the method statement to those doing the job and test their understanding

Display the method statement on a noticeboard in the office

Make sure that those doing the job have read the method statement

6 / 72

In deciding what control measures to take, following a risk assessment that has revealed a risk, what measure should you always consider first?

Adapt the work to the individual

Make sure personal protective equipment (PPE) is available

Avoid the risk altogether if possible

Give priority to measures that protect the whole workforce

7 / 72

What is regarded as the last resort in the hierarchy of control for operatives' safety when working at height?

Access tower scaffold

Safety harness

Mobile access tower

Mobile elevating work platform (MEWP)

8 / 72

How should cylinders containing liquefied petroleum gas (LPG) be stored on site?

In a secure storage container at the back of the site

In a locked cellar with clear warning signs

Covered by a tarpaulin to shield the compressed cylinder from sunlight

In a locked cage at least 3 m from any oxygen cylinders

9 / 72

How should access be controlled if people are working in a riser shaft?

By those who are working in it

By a site security operative

By a permit to work system

By the main contractor

10 / 72

Which of the following precautions should be taken to prevent a dumper that is tipping material into an excavation from falling into it?

Dumpers should be kept 5 m away from the excavation

Stop blocks should be provided, parallel to the trench and appropriate to the vehicle's wheel size

Cones or signage should be erected to indicate the safe tipping point

Dumper drivers are required to judge the distance carefully or be given stop signals by another person

11 / 72

What is the advantage of using safety nets rather than a harness and fall-arrest lanyard?

Workers' lanyards can get entangled with other workers' lanyards

Safety nets can be rigged by anyone

Safety nets do not need inspecting

Safety nets provide collective fall protection

12 / 72

When putting people to work above public areas, what should be your first consideration?

To prevent anything falling onto people below

To minimise the number of people below at any one time

To let the public know what you are doing

To prevent complaints from the public

13 / 72

What does the term lower exposure action value (80 decibels (dBA)) mean, when referring to noise?

The noise level at which the worker can request hearing protection

The level of noise which must not be exceeded on the site boundary

The noise level at which the worker must wear hearing protection

The average background noise level

14 / 72

What does the proactive monitoring of health and safety procedures involve?

Looking at the work to be done, what could go wrong and how it could be done safely

Ensuring that staff always do the work that they have been instructed to do safely

Checking that all staff read and understand all health and safety notices

Deciding how to prevent accidents similar to those that have already occurred

15 / 72

In considering what measures to take to protect workers against risks to their health and safety, when should personal protective equipment (PPE) be considered?

First, because it is an effective way to protect people

First, as the only practical measure

Only when the risks cannot be eliminated by other means

Never, as using PPE is bad practice

16 / 72

Which of the following should be the first consideration if you need to use a hazardous substance?

What health surveillance arrangements will be needed

How to monitor the exposure of workers in the workplace

How to minimise risk and control exposure

What instruction, training and supervision to provide

17 / 72

At what minimum noise level must you provide hearing protection to workers if they ask for it?

87 decibels (dBA)

85 decibels (dBA)

90 decibels (dBA)

80 decibels (dBA)

18 / 72

Which two of the following factors must be considered when providing first-aid facilities on site?

The hazards, risks and nature of the work carried out

The difficulty in finding time to purchase the necessary equipment

The cost of first-aid equipment

The number of people expected to be on site at any one time

The space in the site office to store the necessary equipment

19 / 72

In the colour coding of electrical power supplies on site, what voltage does a blue plug represent?

230 volts

50 volts

400 volts

110 volts

20 / 72

What should be used to protect passers-by from getting arc eye when electric welding is about to start on your site?

Warning signs

Nothing

Screens

Personal protective equipment (PPE)

21 / 72

Ideally, where should a safety net be rigged?

6 m below where you are working

2 m below where you are working

At any height below the working position

Immediately below where you are working

22 / 72

What is the purpose of using a permit to work system?

To establish a controlled, safe system of work

To enable tools and equipment to be properly checked before work starts

To ensure that the job is carried out by the easiest method

To ensure that the job is carried out quickly

23 / 72

If a scaffold is not complete, which of the following actions should be taken by the supervisor?

Make sure that the scaffolders complete the scaffold

Display a warning notice and tell operatives to use the scaffold with care

Tell operatives not to use the scaffold

Prevent access to the scaffold and add warning signage

24 / 72

What should be included in a method statement for working at height? Give three answers.

The cost of the job and the time it will take

How falls are to be prevented

How much insurance cover will be required

Who will supervise the job on site

The sequence of operations and the equipment to be used

25 / 72

Which of the following is a fall-arrest system?

Safety harness and lanyard

Guard-rail and toe-board

Mobile elevating work platform (MEWP)

Mobile access tower

26 / 72

Under the Construction (Design and Management) Regulations 2015, what must be provided before construction work starts, and then maintained until the end of the project?

Adequate welfare facilities

A premises log book

A safety log book

A car park or other parking facilities

27 / 72

When the Construction (Design and Management) Regulations 2015 apply, what must be in place before construction work begins?

The construction phase plan

The health and safety file

The method statement

The construction contract agreement

28 / 72

What is the minimum height of the main guard-rail on a scaffold?

910 mm

950 mm

1000 mm

875 mm

29 / 72

Where should an emergency escape route take you to?

The open air

A first-aid room

A place of safety

The ground

30 / 72

Why must a residual current device (RCD) be used in conjunction with 230-volt electrical equipment?

It lowers the voltage

It quickly cuts off the power if there is a fault

It saves energy and lowers costs

It makes the tool run at a safe speed

31 / 72

Why is it important that hazards are identified?

They must all be eliminated before work can start

So that toolbox talks can be given on the hazards

They must all be notified to the Health and Safety Executive (HSE)

They have the potential to cause injury or harm

32 / 72

What is the purpose of the health and safety file that is handed to the client at the end of the project?

To help people who have to carry out work on the structure in the future

To record the accident statistics of the construction project

To help prepare the final accounts for the structure

To record the health and safety standards of the structure

33 / 72

You have to use a new substance for the first time and need to carry out a COSHH assessment. What are the two main things you will need?

The age of the people doing the work

The delivery note

Your company's safety policy

The details of where, who and how you will be using the substance

The safety data sheet

34 / 72

At what decibel (dBA) level does it become mandatory for an employer to establish hearing protection zones?

85 decibels (dBA)

80 decibels (dBA)

95 decibels (dBA)

90 decibels (dBA)

35 / 72

Who should you inform if someone tells you that they have work-related hand-arm vibration syndrome (HAVS)?

The Health and Safety Executive (HSE)

The local Health Authority

The nearest hospital

The person's doctor

36 / 72

How long must you keep inspection records under the Construction (Design and Management) Regulations 2015?

For three months after the inspection has been carried out

Only until the project is complete

For one week on site before sending them to head office

Until the construction work is complete and then for three months

37 / 72

On a scaffold, what must be the largest unprotected gap between any guard-rail, toe-board, barrier or other similar means of protection?

500 mm

470 mm

600 mm

400 mm

38 / 72

If there is a fatal accident or a reportable dangerous occurrence on site, when must the Health and Safety Executive (HSE) be informed?

Within seven days

Immediately

Within five days

Within ten days

39 / 72

Before allowing a lifting operation to be carried out, where should you ensure that the sequence of operations is recorded to enable a safe lift?

In a lifting operation toolbox talk

In an approved lifting plan or method statement

In the crane hire contract

In a risk assessment

40 / 72

What is your least reliable source of information when assessing the level of vibration from a powered hand tool?

Vibration data from the Health and Safety Executive's (HSE) master list

Vibration figures taken from the tool manufacturer's handbook

Your own judgement based upon observation or experience

In-use vibration measurement of the tool

41 / 72

The Beaufort Scale is important when working at height externally. What does it measure?

Wind speed

Air temperature

The load-bearing capacity of a flat roof

The load-bearing capacity of a scaffold

42 / 72

When does an employer have to prepare a written health and safety policy?

If they employ a safety officer

If they employ three people or more

If the work is going to last more than 30 days

If they employ five people or more

43 / 72

Which of the following tasks would you expect the appointed person for first aid to carry out?

They should contact the emergency services when required

They should provide all of the care normally carried out by a first aider

They should provide most of the care normally carried out by a first aider

They should only apply splints to broken bones

44 / 72

Why is it dangerous to use inflatable airbags for fall arrest if they are too big for the area to be protected?

The pressure in the bags will cause them to burst

The inflation pump will become overloaded

They will exert a sideways pressure on anything that is containing them

They will not fully inflate

45 / 72

Which of the following is a significant hazard when excavating alongside a building or structure?

Undermining or weakening the foundations of the building

Damaging the surface finish of the building or structure

Noise and vibration affecting the occupiers of the building

Excavating too deeply into soft ground

46 / 72

On the site electrical distribution system, which colour plug indicates a 400-volt supply?

Blue

Black

Red

Yellow

47 / 72

How could a site worker check if the residual current device (RCD) through which a 230-volt hand tool is connected to the supply is working correctly?

Run the tool at top speed to see if it cuts out

Switch the tool on and off

Switch the power on and off

Press the test button on the RCD unit

48 / 72

When planning possible work in a confined space, what should be the first consideration?

How many operatives will be required

What personal protective equipment (PPE) will be needed

How to avoid the need for operatives to enter the space

How long the job will take

49 / 72

The significant findings of risk assessments must be recorded when how many people are employed?

Seven or more

Six or more

Five or more

Three or more

50 / 72

What must edge protection be designed to do?

Allow persons to work on both sides of it

Prevent people and materials from falling

Secure tools and materials close to the edge

Warn people where the edge of the roof is

51 / 72

What is the main danger of leaving someone who has fallen suspended in a harness for too long?

They may suffer loss of consciousness and further injury

The anchorage point may fail

They may try to climb back up the structure and fall again

It is a distraction for other workers

52 / 72

From a safety point of view, which of the following should be considered first when deciding on the number and location of access and egress points on a site?

Site security

Access for the emergency services

Access for heavy vehicles

Off-road parking for cars and vans

53 / 72

What regulation contains details of the welfare facilities that must be provided on a construction site?

The Management of Health and Safety at Work Regulations

The Control of Substances Hazardous to Health (COSHH)

The Workplace (Health, Safety and Welfare) Regulations

The Construction (Design and Management) Regulations

54 / 72

Under the requirements of the Work at Height Regulations, what must the minimum width of a working platform be?

Four scaffold boards wide

Two scaffold boards wide

Three scaffold boards wide

Suitable and sufficient for the job in hand

55 / 72

When should guard-rails be fitted to a working platform?

If it is possible to fall 2 m

Only if materials are being stored on the working platform

At any height if a fall could result in an injury

If it is possible to fall 3 m

56 / 72

When do the Work at Height Regulations require a working platform to be inspected by a competent person?

After it has been erected and then at intervals not exceeding 10 days

After it has been erected and then at intervals not exceeding seven days

Only after it has been erected

After it has been erected and then at monthly intervals

57 / 72

Under the Construction (Design and Management) Regulations 2015, when the contractor sets a person to work on a construction site, what must they ensure that person has, or be in the process of, obtaining?

The right skills, knowledge, training and experience

The relevant competency card

A hard hat, hi-vis clothing and safety footwear

A relevant qualification for the work to be undertaken

58 / 72

What should be the capacity of a spillage bund around a fuel storage tank, in addition to the volume of the tank?

30% (130% of the total content)

50% (150% of the total content)

10% (110% of the total content)

75% (175% of the total content)

59 / 72

What should you do if you notice that operatives working above a safety net are dropping off-cuts of material and other debris into the net?

Nothing, as the debris is all collecting in one place

Have the net cleared and inspected, then ensure it is not allowed to happen again

Ensure that the net is cleared of debris weekly

Ensure that the net is cleared of debris daily

60 / 72

In the context of a risk assessment, what does the term risk mean?

The likelihood that you, or someone else, could be harmed, and how serious any harm could be

Any unsafe act or condition which could cause loss, injury or damage

Any work activity that can be described as hazardous or dangerous

Anything that could cause harm to you or another person

61 / 72

What danger is created by excessive oxygen in a confined space?

An increased working time inside the work area

An increased flammability of combustible materials

An increase in the breathing rate of workers

A false sense of security

62 / 72

A design feature of some airbags used for fall arrest is a controlled leak rate. If you are using these, what must you ensure about the inflation pump?

It must be electrically powered

It must run all the time while work is carried out at height

It must be switched off from time to time to avoid over-inflation

It must be switched off when the airbags are full

63 / 72

Following a scaffold inspection under the Work at Height Regulations, how soon must a report be given to the person on whose behalf the inspection was made?

Within 12 hours

Within 2 hours

Within 24 hours

Within 6 hours

64 / 72

Why may a young person be more at risk of having an accident?

They are usually left to work alone to gain experience

Legislation does not apply to anyone under 18 years of age

They are less likely to wear personal protective equipment (PPE)

They have less experience and may not recognise danger or understand fully what could go wrong

65 / 72

What is the maximum unprotected gap allowed between any guard-rail, toe board, barrier or other similar means of protection on a scaffold?

600 mm

470 mm

500 mm

400 mm

66 / 72

Where must the number of people who may be carried in a passenger hoist on site be displayed?

On a legible notice displayed during the site induction

On a legible notice handed to the hoist operator

On a legible notice within the cage of the hoist

On a legible notice in the site welfare area

67 / 72

When is it advisable to take precautions to prevent people, plant or materials falling into an excavation?

When the excavation is 1.2 m or more deep

When there is a risk from an underground cable other service

At all times

When the excavation is 2 m or more deep

68 / 72

Under the Construction (Design and Management) Regulations 2015, where would you find the arrangements for managing health and safety for the project you are working on?

In the construction phase plan

In the designer's risk assessment

In the health and safety file

In the contract documentation

69 / 72

Which piece of equipment is used with a cable avoidance tool (CAT) to detect cables?

Gas detector

Metal detector

Compressor

Signal generator

70 / 72

Where should liquefied petroleum gas (LPG) cylinders supplying an appliance in a site cabin be positioned?

Outside the cabin

Inside the cabin next to the appliance

Inside the cabin in a locked cupboard

Under the cabin

71 / 72

What must happen if a prohibition notice is issued by an inspector of the Health and Safety Executive (HSE) or Local Authority?

The work in hand can be completed, but no new works started

Work can continue, as long as a risk assessment is carried out

The work can continue if extra safety precaution are taken

The work that is subject to the notice must stop

72 / 72

What is the significance of a weekly or daily personal noise exposure of 87 decibels (dBA)?

It is the exposure limit value and must not be exceeded

It is the lower action value and no action is necessary

It is the upper action value and hearing protection must be issued

It is the peak sound pressure and all work must stop

Your score is

The average score is 80%

Exit

How was the test? Please Submit your Rating and give us a feedback!

Thank you for taking the time to complete a mock test on our website. We appreciate your effort and dedication.

We wish you the best of luck in your preparation and future exams. If you have any feedback or suggestions, please let us know.

CSCS Supervisor Mock Test

Related Practice Tests

Practice Test 1

Practice Test 2

Practice Test 3

Practice Test 4

Practice Test 5

Leave a Reply Cancel reply