CSCS Ductwork Mock Test

0 votes, 0 avg

Specialists Test

HVACR - Ductwork

1 / 45

When jointing plastic-coated metal ductwork, which of the following methods of jointing presents the most serious risk to health?

Fixing nuts and bolts

Taping

Welding

Riveting

2 / 45

In addition to a safety helmet and protective footwear, what personal protective equipment (PPE) should you wear when using a hammer drill?

Barrier cream and respiratory protective equipment

Hearing protection, respiratory protective equipment and eye protection

Gloves and breathing apparatus

Hearing protection, breathing apparatus and barrier cream

3 / 45

If you are asked to install high-level ductwork from a platform that has no edge protection and is located above an open stairwell, what should you do?

Not start work until your work platform has been fitted with guard-rails and toe-boards

Get on with the job, but keep away from the edge of the platform

Get on with the job, provided that if you fall the stairwell guard-rail will prevent you from falling further

Get on with the job, ensuring that a workmate stays close by

4 / 45

What additional control measure must be put in place when welding in-situ galvanised ductwork?

Fume extraction

Hearing protection

Warning signs

Screens

5 / 45

What should be done before a mobile tower is moved?

A permit to work must be issued

Arrangements must be made with the forklift truck driver

All people and equipment must be removed from the platform

The principal contractor must give their approval

6 / 45

When a new piece of plant has been installed but has not been commissioned, how should it be left?

With all valves and switches locked off

With all valves and switches clearly labelled

With all valves and switches turned off

With all valves and switches turned on and ready to use

7 / 45

How should you leave the area around ductwork after using a solvent-based sealant?

Ensure that the lids are left off tins of solvent

Leave inspection covers off and erect no smoking signs

Remove any safety signs or notices

Seal up all the open ends to ensure that dirt cannot get into the system

8 / 45

When planning a lifting operation, how should the sequence of operations to enable a safe lift be confirmed?

By verbal instructions

Via a notice in the canteen

In a radio telephone message

In a method statement

9 / 45

You have to carry out a job over a few days on the flat roof of a two-storey building, about 1 m from the edge of the roof, which has a low parapet. How should you reduce your risk of falling?

Carry on with the job, provided that you don't get dizzy with heights

Get your mate to do the work, while you hold on to them

Ask for double guard-rails and a toe-board to be installed

Use a full body harness, lanyard and anchor while doing the job

10 / 45

What must be done first before any roof work is carried out?

The operatives working on the roof must be trained in the use of safety harnesses

A weather forecast must be obtained

A risk assessment must be carried out

Permits to work must be issued only to those allowed to work on the roof

11 / 45

If you spill some oil on the floor and you do not have any absorbent material to clean the area, what should you do?

Spread it about to lessen the depth

Do nothing, as it will eventually soak into the floor

Keep people out of the area and inform your supervisor

Warn other people as they tread through it

12 / 45

When carrying out solvent welding on plastic ductwork, what particular safety measure must be applied?

The supervisor must be present

It must be done in daylight

A hard hat must be worn

The area must be well ventilated

13 / 45

Which two of the following should you use when cutting aluminium or tin ductwork that has been pre-insulated with fibreglass?

A blowtorch

A set of tin snips

Respiratory protective equipment

A chisel

A hacksaw

14 / 45

What is the safest way to move a fan-coil unit some distance?

Roll it end-over-end

Drag it

Use a trolley or other manual handling aid

Get a workmate to carry it with you

15 / 45

What is the first thing you should do after getting on to the platform of a correctly erected mobile tower?

Check for overhead power lines

Check that the brakes are locked on

Close the access hatch to prevent falls of personnel, tools or equipment

Make sure that the tower does not rock or wobble

16 / 45

If you find a coloured wire sticking out of an electrical plug what is the correct action to take?

Mark the item as defective and follow your company procedure for defective items

Push it back into the plug and carry on working

Pull the wire clear of the plug and report it to your supervisor

Take the plug apart and carry out a repair

17 / 45

How should extension leads in-use on site be positioned?

They should be laid out in the shortest, most convenient route

They should be located so as to prevent a tripping hazard

They should be raised on bricks

They should be coiled on a drum or cable tidy

18 / 45

Where should liquefied petroleum gas (LPG) cylinders be positioned when supplying an appliance in a site cabin?

Outside the cabin

Inside the cabin in a locked cupboard

Under the cabin

Inside the cabin next to the appliance

19 / 45

If you are using a genie hoist and notice that part of the hoist is buckling slightly, what should you do?

Carry on with the job, while keeping an eye on the buckling metal

Get the job finished quickly

Lower the load immediately

Straighten out the buckled metal and then get on with the lifting operation

20 / 45

Which of these statements is true in relation to the safe working load (SWL) of lifting equipment?

It is the absolute maximum safe working load

It is never marked on the equipment but kept with the test certificates

It may be exceeded by no more than 25%

It is provided for guidance only

21 / 45

Where it is necessary to enter ductwork, which are the two main factors that need to be considered?

The cleanliness of the ductwork

The strength of the ductwork and its supports

Whether you need to wear kneepads

Working in a confined space

What the ductwork will carry in the future

22 / 45

If you have to dismantle some waste-extract ductwork, what is the first thing you should do?

Arrange for a skip to put it in

Check that the duct supports are strong enough to cope with the dismantling

Ensure there is a certificate of cleanliness in place before commencing work

Make sure there are enough disc cutters to do the job

23 / 45

What must you ensure before using a ladder?

That an apprentice or workmate is standing by in case you slip and fall

That the weather forecast is for a bright, clear day

That no-one else has booked the ladder for their work

That it is secured to prevent it from moving sideways or sliding outwards

24 / 45

When positioning and erecting a stepladder, which of the following is essential for its safe use?

It has a tool tray towards the top of the steps

Your supervisor has positioned and erected the steps

The restraint mechanism is spread to its full extent

You will be able to reach the job by standing on the top step

25 / 45

What is the recommended maximum height for a free-standing mobile tower?

2 m

12 m

There is no restriction

The height recommended by the manufacturer

26 / 45

What should you do if you need additional temporary wiring for your power tools whilst working on site?

Find some cable and extend the wiring yourself

Speak to an electrician and ask them to do the temporary wiring

Disconnect a longer cable serving somewhere else and reconnect it to where you need it

Stop work until an authorised supply has been installed

27 / 45

Before taking down a run of ductwork, what is the first thing you should do?

Assess the volume of waste and get an appropriate sized skip

Clean the ductwork to remove all dust

Cut through the support rods

Assess the task to be undertaken and check its support system

28 / 45

When assembling a mobile tower what major hazard must you be aware of?

Overhead service cables

False ceilings

Water pipes

Cable trays

29 / 45

What is the best form of access to use, when installing a run of ceiling-mounted ductwork across a large open space?

Stepladder

Metal trestles

Wooden trestles

Mobile tower

30 / 45

Who should carry out leakage testing of a newly installed ductwork system?

The installation contractor

A trained and competent person

The designer

The property owner

31 / 45

If you are working where welding is being carried out, what should be provided to protect you from welding flash?

Warning notices

A hi-vis vest

A fire extinguisher

Screens

32 / 45

What should you do before painting the external surface of ductwork?

Read the COSHH assessment

Switch off the system

Clean the paintbrushes

Put on eye protection

33 / 45

While fitting a fire damper into a ductwork system you notice that, due to a manufacturing fault, it may not operate properly. What should you do?

Install it anyway, as it is

Fix it so that it stays open, and then install it

Leave it out of the ductwork system altogether

Not fit the damper and report the fault

34 / 45

When do you need to wear eye protection while drilling through a wall?

Only when drilling overhead

Only when the drill bit exceeds 20 mm

Only when drilling through concrete

Always, whatever the circumstances

35 / 45

Which item of electrical equipment does not require portable appliance testing?

Battery-powered rechargeable drill

110-volt portable halogen light

Electric kettle

110-volt electrical drill

36 / 45

When using a material hoist you notice that the lifting cable is frayed. What should you do?

Be very careful when using the hoist

Straighten out the cable using mole grips

Get the job done as quickly as possible

Do not use the hoist, and report the problem

37 / 45

How should you position the exhaust of an engine-driven generator that has to be run inside a building?

In a riser

In another room

In a stairwell

Outside the building

38 / 45

What is edge protection designed to do?

Make access to the roof easier

Secure tools and materials close to the edge

Prevent rainwater running off the roof onto workers below

Prevent the fall of people and materials

39 / 45

When working in a riser, how should access be controlled?

By the main contractor

By a site security operative

By a permit to work system

By those who are working in it

40 / 45

Which of the following do you not need to do before using a cleaning agent or biocide in a ductwork system?

Read the COSHH assessment for the material, carry out a risk assessment and produce a method statement for the work

Ask for advice from the cleaning agent or biocide manufacturer

Check what the ductwork will carry in the future

Consult the building occupier

41 / 45

What must be clearly marked on all lifting equipment?

The next test date

The safe working load

The name of the manufacturer

The specification of material from which it is made

42 / 45

What should folding stepladders be used for?

Short-term works

General access on site

All site activities where a straight ladder cannot be used

Getting on and off mobile towers

43 / 45

Which of the following do you not need to do before cleaning a system in industrial, laboratory or other premises where you might encounter harmful particulates?

Collect a sample from the ductwork

Prepare a job-specific risk assessment and method statement

Examine the system

Run the system under overload conditions

44 / 45

If you are removing a run of ductwork in an unoccupied building and notice a hypodermic syringe behind it, what should you do?

Ensure the syringe is empty, remove it and place it with the rubbish

Wear gloves, use grips to remove the syringe to a safe place and report your find

Notify the supervisor, cordon off the area and call the emergency services

Wear gloves, break the syringe into small pieces and flush it down the drain

45 / 45

A person who has been using a solvent-based ductwork sealant is complaining of headaches and feeling sick. What is the first thing you should do?

Get them a drink of water and a headache tablet

Get them out to fresh air and make them rest

Let them carry on working but try to keep a close watch on them

Make an entry in the accident book

Your score is

The average score is 88%

Exit

How was the test? Please Submit your Rating and give us a feedback!

Thank you for taking the time to complete a mock test on our website. We appreciate your effort and dedication.

We wish you the best of luck in your preparation and future exams. If you have any feedback or suggestions, please let us know.

Leave a Reply Cancel reply

Like this: