CSCS Lift and Escalator Mock Test

0 votes, 0 avg

Specialists Test

Lifts and Escalators

1 / 49

What are the appropriate types of tools and equipment for working on electrical lift-control equipment?

Insulated tools and an insulating mat

Non-insulated tools

Any tools and an insulating mat

No tools are allowed near electrical equipment

2 / 49

Which statement is true when using an authorised lifting accessory marked with its safe working load?

Double the safe working load if people need to be lifted

Never exceed the safe working load

The safe working load is only for guidance

Halve the safe working load if the equipment is damaged

3 / 49

If a switch needs to be changed in the pit but the isolator is in the machine room 12 floors above, what should you do?

Isolate the power and then lock and tag the isolator

Use insulated tools

Stand on a rubber mat

Risk assess the situation and change the switch with the power on because it is control voltage

4 / 49

How should you connect a car light supply to a 240-volt supply (240-volt fused spur)?

Switch off the spur and then connect it

Switch off the spur, remove the fuse and then connect it

Isolate and lock off the incoming supply and then connect it

Connect it with the power on

5 / 49

Which two of the following actions must be carried out by an authorised person working alone?

Ensuring their timesheet is accurate and countersigned

Ensuring that the lift pit is free from water and debris

Registering their presence with the site representative before starting work

Establishing suitable arrangements to ensure the monitoring of their wellbeing

Notifying the site manager of the details of their work

6 / 49

What checks do you need to carry out before using lifting equipment?

That the chains are knotted to the correct length

A drop check

That the lifting tackle states the date of manufacture

That it is free from defects and has a current examination certificate

7 / 49

What should you do if the lifting accessory you are about to use is defective?

Do not use it and inform your supervisor

Only use it for small lifts under 1 tonne

Try to fix it

Only use it for half its safe working load

8 / 49

Who is allowed to safely release trapped passengers?

Anyone

Only the emergency services

Only a trained and authorised person

The site manager

9 / 49

What should be applied to the main isolator of a traction lift to prevent it starting accidentally?

A residual current device (RCD)

Lower-rated fuses

A warning notice

A lock-out device

10 / 49

What precaution must you take if the landing doors are to be open while work goes on in the lift pit?

Post a notice on the wall next to the doors

Ask someone to guard the open doors while you work

Do the job when there are not many people about

Erect a suitable barrier and secure it in front of the landing doors

11 / 49

What must you ensure to prevent unauthorised access to unoccupied machine equipment space?

That a person is posted to prevent access

That the power supply is isolated

That a sign is posted to warn trespassers

That the access door is locked

12 / 49

What is required on each landing of a new lift shaft before entrances and doors are fitted?

Bright lighting

A substantial secure barrier to prevent falls

A warning notice

Orange plastic netting across the opening

13 / 49

If landing doors are not fitted to a lift on a construction site, what is the minimum height of the barrier that must be fitted instead?

950 mm

650 mm

810 mm

740 mm

14 / 49

When must you not wear rings, bracelets, wrist watches, necklaces and similar items?

When working on site generally

After leaving home for work

When driving a company vehicle

When working near or on electrical or moving equipment

15 / 49

When you gain access to a car top, how should you test that the car-top stop switch operates correctly?

By trying to move the car in the down direction

By trying to move the car in the up direction

By flicking the switch on and off rapidly

By measuring with a multimeter

16 / 49

Which of the following types of fire extinguisher should not be used if there is a fire in a lift or escalator controller?

Dry powder

Dry chemical

Water

Carbon dioxide

17 / 49

What is fitted to prevent injury from an overspeed governor?

A restrictor

A rope

A switch

A guard

18 / 49

When installing a partially enclosed or observation lift, what safe system of work can you use to prevent injury to people below?

Secure tools to prevent them falling off

Put up a sign

Only carry out essential work using minimum tools

Do not use heavy tools

19 / 49

When working in the pit, when should the lift not be positioned towards the top of the shaft?

When you are testing the buffers

When the power supply is cut

When the hydraulic fluid level is low

When work needs to be done on the underside of the lift

20 / 49

Which statement is true when working on an energised car?

Ensure that your lanyard is clipped to a guide bracket or similar anchorage on the shaft

Always attach your lanyard to the car top while standing on the landing

Make sure you step onto the landing with your lanyard still attached to the car

Always check your lanyard is unclipped before getting off the car top

21 / 49

If you arrive on site and find the lift mains isolator switched off, what should you do?

Shout down the shaft and, if no-one responds, switch it on and get on with your work

Switch it on and get on with your work

Switch it on and check the safety circuits to see if there is a fault

Contact the person in control of the premises to find out if they had switched it off

22 / 49

What is an essential action before gaining access into the escalator or passenger conveyor?

That the mains switch is in the 'On' position

That the drive mechanism is lubricated

That the mains switch is locked out and tagged

That all steps are removed

23 / 49

When handling stainless steel car panels, which of the following items of personal protective equipment (PPE) should you wear in addition to safety footwear?

Hand barrier cream

Latex gloves

Suitable safety gloves, such as rigger type gloves

Hearing protection

24 / 49

A lifting beam at the top of the lift shaft is marked with a safe working load of 800 kg but the brickwork around the beam is cracked and appears to be loose. What should you do?

Not use the beam and speak to your supervisor

De-rate the beam by 75%

Only lift loads not exceeding 400 kg

Use the beam as normal

25 / 49

What is secured at the entry and exit points of an escalator or passenger conveyor to prevent people falling into the machine or machine space?

Safety notices

Safety barriers

Escalator machine equipment guards

Machine tank covers

26 / 49

When is it acceptable to work on the top of a car without a car-top control station?

When only one person is working on it

When there is no other way to work on it

When two engineers are working on it

When the unit has been locked out and tagged

27 / 49

What is the statutory period of examination for lifting equipment that is used to lift people?

At least every 12 months

At least every 6 months

At least monthly

Once every 2 years

28 / 49

If a counterweight screen is not fitted or has been removed, what should you do before starting work?

Give a toolbox talk on guarding

Carry out a further risk assessment to establish a safe system of work

Issue and wear appropriate personal protective equipment (PPE)

Nothing - just get on with the job as normal

29 / 49

What is the minimum size of gap between the edge of the work platform and the hoist way wall that is regarded as a fall hazard?

300 mm

250 mm

330 mm

450 mm

30 / 49

What is the most effective way of reducing the likelihood of being struck by falling objects?

Put warning signs up in the area

Don't work below another person

Install suitable debris netting

Wear a safety helmet with a chin strap

31 / 49

Which of these statements is not true?

You should secure your tools out of your standing area when working on top of the car

The car top should be clean and free from grease and oil spills

A stop switch must be within 1.5 m of the front of the car

Before trying to access the hoist way, you should decide whether the work will need the power supply to be live

32 / 49

If the main contractor wants to use an unfinished lift to move some equipment to an upper floor, what should you do?

Tell them to talk to your supervisor

Help to ensure the load is correctly positioned

Allow them to use the lift but take no responsibility for any accidents

Ask for the weight of the equipment

33 / 49

A set of chain blocks has been delivered to site with an examination report stating that they were examined by a competent person a month ago. The hook is obviously damaged. What action do you take?

Do not use the blocks and inform your supervisor

Use the blocks as the examination report is current

Use the blocks at half the safe working load

Use the blocks until replacement equipment arrives

34 / 49

What should be fitted to the main sheave and diverter to prevent injury from rotating equipment?

Safety notices

Movement sensors

Clutching assemblies

Guards

35 / 49

A large, heavy, balance weight frame is delivered to site on a lorry with no crane and there is no lifting equipment available on site. What should you do?

Unload it manually

Slide it down planks

Tip the load off the lorry

Arrange for it to be re-delivered on a suitable lorry

36 / 49

At what stage in the installation of a lift should guarding be fitted to the lift machine?

During commissioning

When handing over to the client

At the end of the job

Before the machine can be operated

37 / 49

What is the last thing you should do before getting off a car top through open landing doors when the car-top control is within 1 m of the landing threshold?

Set the car-top control to test

Press the stop button and switch the car-top control to normal

Ensure that the car-top stop button is set to stop and the car-top control remains set to test

Turn off the shaft lights and switch the car-top control to normal

38 / 49

What must you do before moving the steps or pallet band of an escalator or passenger conveyor?

Check that no unauthorised people are on the equipment

Check that there are no sharp edges on the steps

Check that there is a clear route of escape

Check that a fire extinguisher is available

39 / 49

What is the correct method for disposing of used or contaminated oil?

Pour it down a roadside drain

Decant it into a sealed container and place in a skip

Dilute it with water and pour it down a sink

Dispose of it through a registered waste process

40 / 49

When installing a new rope, what should you do if you notice a damaged section where something heavy has fallen onto the coil?

Add an extra termination

Reject the rope

Fit the rope anyway

Cut out the damaged section

41 / 49

Who is responsible for the keys when a padlock has been applied to a lock-out device?

The individual applying the lock

The site supervisor

The site manager

The person nearest the lock-out device

42 / 49

Following the initial inspection, how often should a scaffold in a lift shaft be inspected by a competent person?

At least every day

At least every 14 days

At least every 7 days

There is no set period between inspections

43 / 49

What is the first thing to do after opening the landing doors and before accessing the car-top of an operating lift?

Make sure the lift has stopped

Press the car-top stop button

Put the car-top control in the test position

Chock the landing doors open

44 / 49

Who should fit a padlock and tag to an electrical lock-out guard?

Anyone authorised to work on the unit

Only the person who fitted the lock-out guard

Only the senior engineer

Only the manufacturer

45 / 49

What is the main cause of injury and absence for workers in the lift and escalator industry?

Falls

Contact with moving parts

Electrocution

Manual handling

46 / 49

What needs to be checked before any hot work takes place in the lift installation?

If the local fire services need to be notified

If a hot-work permit is required

The weight and size of the welding equipment

How long the task will take

47 / 49

If the escalator or passenger conveyor has an external machine room, which statement applies to its access doors?

They should be unlocked at all times in case of an emergency

They should be smoke proof in case of a fire

They should be capable of being locked from both sides and be marked with an appropriate safety sign

They should be capable of being locked on the inside only and be marked with the appropriate safety sign

48 / 49

What must you do first, before entering the pit of an operating lift?

Verify the pit stop switch

Fit pit props

Switch the lift off

Position the access ladder

49 / 49

What must you ensure if the trapdoor or hatch has to be left open while you work in the machine room?

That a sign is posted to warn others that you are working there

That a suitable barrier is put in place around the trapdoor or hatch

That the distance from the trapdoor or hatch to the floor below does not exceed 2 m

That there is sufficient light available for the work

Your score is

The average score is 0%

Exit

How was the test? Please Submit your Rating and give us a feedback!

Thank you for taking the time to complete a mock test on our website. We appreciate your effort and dedication.

We wish you the best of luck in your preparation and future exams. If you have any feedback or suggestions, please let us know.

Leave a Reply Cancel reply